Canoga-perkins CanogaOS Command Reference Manual de usuario Pagina 327
- Pagina / 855
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
CanogaOS Command Line Reference Revision 1.02
Proprietary & Confidential Canoga Pertkins Metro Ethernet Switches Page 327 of 855
Usage
By default, the system uses BGP version 4 and on request dynamically negotiates down to version 2. Using
this command disables the router’s version-negotiation capability and forces the router to use only a specified
version with the neighbor.
Examples
Switch# configure terminal
Switch(config)# router /jointfilesconvert/1661109/bgp 12
Switch(config-router)# neighbor 10.10.10.10 version 4
16.73 neighbor weight
Use this command to set default weights for routes from this neighbor.
Use the no parameter with this command to remove a weight assignment.
Command Syntax
(no) neighbor NEIGHBORID weight WEIGHT
NEIGHBORID = A.B.C.D|X:X::X:X|TAG
A.B.C.D Specifies the address of the BGP neighbor in IPv4 format.
X:X::X:X Specifies the address of the BGP neighbor in IPv6 format.
TAG Name of an existing peer-group. For information on how to create peer groups, refer to the
neighbor peer-group and neighbor remote-as commands. When this parameter is used with a
command, the command applies on all peers in the specified group.
WEIGHT= <0-65535> Specifies the weight this command assigns to the route.
Command Mode
Router mode
Usage
Use this command to specify a weight value to all routes learned from a neighbor. The route with the highest
weight gets preference when there are other routes on the network.
Unlike the local-preference attribute, the weight attribute is relevant only to the local router.
The weights assigned using the set weight command overrides the weights assigned using this command.
Examples
Switch# configure terminal
Switch(config)# router /jointfilesconvert/1661109/bgp 12
Switch(config-router)# neighbor 10.10.10.10 weight 60
- CanogaOS 1
- Command Reference 1
- CAUTION! 2
- ATTENCION! 2
- NOTICE! 2
- CANOGA PERKINS CORPORATION 3
- Table of Content 5
- 1 Preface 42
- 1.4 Related Publications 43
- 1.5 Obtaining Documentation 43
- Documentation Feedback 44
- 2.1 User EXEC Mode 45
- 2.2 Privileged EXEC Mode 45
- 2.4 config-vlan Mode 46
- 2.5 VLAN Configuration Mode 46
- 2.6 Line Configuration Mode 47
- 3 configure terminal 48
- 3.2 enable 49
- 3.3 end 50
- 3.4 exit (global) 50
- 3.5 exit (EXEC) 51
- 3.6 quit 52
- 3.7 terminal length 53
- 3.8 service terminal-length 54
- 3.9 cipher detect 55
- 3.10 enable password 55
- 3.11 enable secret 56
- 4 Interface Commands 59
- 4.3 exec-timeout 60
- 4.4 exit(global) 61
- 4.5 line-password 61
- 4.6 login 62
- 4.7 privilege 63
- 4.8 bandwidth 63
- 4.9 clear counters 64
- 4.10 description 65
- 4.11 duplex 65
- 4.12 interface 66
- 4.13 jumboframe 67
- 4.14 management ip address 67
- 4.15 shutdown 68
- 4.16 speed 69
- 4.17 switchport 70
- 4.19 static-channel-group 71
- 4.21 show interface status 73
- discard packet silently 78
- 4.33 storm-control 82
- 5 LACP Commands 84
- 5.3 lacp timeout 85
- 5.4 lacp system-priority 86
- Partner's information: 89
- Local information: 90
- 5.7 show lacp internal 92
- 5.9 show lacp neighbor 97
- Related Commands 104
- 5.11 show channel-group port 105
- 5.12 show lacp counters 113
- 5.13 show lacp sys-id 115
- 5.14 clear lacp counters 115
- 6 VLAN Commands 117
- 6.3 vlan <1-4094> 118
- 6.4 vlan VLAN_LIST 119
- 6.5 show vlan 119
- 6.6 show vlan all 120
- 6.7 show vlan brief 120
- 6.9 vlan classifier activate 121
- 6.10 vlan classifier group 122
- 6.16 switchport access vlan 126
- 6.17 switchport mode access 127
- 6.18 switchport mode trunk 127
- 6.21 switchport trunk native 129
- Defaults 130
- Examples 130
- 7 Spanning-tree Commands 131
- Default 132
- 7.5 spanning-tree hello-time 133
- 7.6 spanning-tree max-age 134
- 7.7 spanning-tree max-hops 135
- 7.12 spanning-tree port 138
- 7.15 spanning-tree path-cost 140
- 7.17 spanning-tree edgeport 141
- 7.29 instance 149
- 7.30 region 150
- 7.31 revision 150
- 7.34 show spanning-tree 152
- 7.35 show spanning-tree all 153
- 7.39 show spanning-tree mst 157
- ERPS Commands 166
- 8.4 erps ring level 168
- 8.5 erps ring mode 169
- 8.7 erps ring edge-mode 171
- 8.9 erps ring srpt 174
- 8.10 erps ring enable 175
- 8.11 erps enable 176
- 8.12 show erps 177
- 8.13 show erps list 177
- 9 QinQ Commands 179
- 9.3 show vlan mapping table 180
- 9.4 switchport mode 180
- 9.9 dot1q ethertype 183
- 9.12 l2protocol-tunnel stp 184
- 9.13 l2protocol-discard stp 185
- 9.15 vlan dot1q tag native 186
- 9.16 show dot1q ethertype 186
- 10 Ethernet CFM Commands 188
- 10.11 CFM loopback tests 194
- 10.12 CFM linktrace tests 195
- Ethernet OAM Commands 203
- 11.2 ethetnet oam mode 204
- 11.3 ethernet oam min rate 204
- 11.4 ethernet oam max-rate 205
- 11.14 ethernet oam timeout 211
- 12 IP Addressing Commands 213
- 12.3 router-id (global) 215
- 12.4 clear ip route static 215
- 12.5 ip route 216
- 12.6 show ip route 217
- 12.8 show ip protocols 219
- 13 ARP Commands 220
- 13.3 clear arp-cache 221
- 13.4 show ip arp 222
- 13.5 show ip arp summary 223
- 14 RIP Commands 224
- 14.3 distance (RIP) 225
- 14.4 ip rip authentication 226
- 14.6 ip rip receive version 228
- 14.7 ip rip receive-packet 229
- 14.8 ip rip send version 229
- 14.9 ip rip send-packet 230
- 14.10 ip rip split-horizen 231
- 14.11 network (RIP) 231
- 14.12 neighbor (RIP) 232
- 14.13 offset-list (RIP) 233
- 14.15 redistribute (RIP) 235
- 14.16 router rip 235
- 14.17 timers basic (RIP) 236
- 14.18 show ip rip database 237
- 14.19 show ip rip interface 238
- 14.20 version (RIP) 239
- 15 OSPF Commands 240
- 15.2 area Default-cost 241
- 15.3 area filter-list 242
- 15.4 area range 243
- 15.5 area stub 244
- 15.6 area virtual-link 245
- 15.7 auto-cost 247
- 15.8 clear ip ospf 247
- 15.9 compatible rfc1583 248
- 15.11 default-metric (OSPF) 250
- 15.12 distance (OSPF) 251
- 15.13 distribute-list (OSPF) 252
- 15.14 ip ospf authentication 252
- 15.16 ip ospf cost 254
- 15.18 ip ospf dead-interval 256
- 15.19 ip ospf disable all 256
- 15.22 ip ospf mtu 259
- 15.23 ip ospf mtu-ignore 260
- 15.24 ip ospf network 260
- 15.25 ip ospf priority 262
- 15.27 ip ospf transmit-delay 263
- 15.28 neighbor (OSPF) 264
- 15.29 network area (OSPF) 265
- 15.31 redistribute (OSPF) 267
- 15.32 router-id (OSPF) 268
- 15.33 router ospf 269
- 15.34 summary-address (OSPF) 270
- 15.35 show ip ospf 271
- 15.37 show ip ospf database 273
- 15.38 show ip ospf interface 274
- 15.39 show ip ospf neighbor 275
- 15.41 timers spf 276
- 16 BGP Commands 278
- 16.2 aggregate-address 279
- 16.3 bgp always-compare-med 279
- 16.7 bgp bestpath med 282
- 16.9 bgp cluster-id 284
- 16.12 bgp dampening 285
- Command Syntax 286
- Command Mode 286
- 16.15 bgp deterministic med 288
- 16.16 bgp enforce-first-as 288
- 16.19 bgp router-id 290
- 16.20 bgp scan-time 291
- 16.21 clear bgp * 291
- 16.23 clear bgp ASN 292
- 16.24 clear bgp external 293
- 16.25 clear bgp peer-group 293
- 16.26 clear ip bgp * 294
- 16.28 clear ip bgp dampening 295
- 16.30 clear ip bgp ASN 297
- 16.31 clear ip bgp external 297
- 16.33 clear ip bgp vrf 299
- 16.34 debug bgp 299
- 16.35 distance 300
- 16.36 exit-address-family 301
- 16.37 ip as-path access-list 301
- 16.38 ip community-list 302
- 16.43 mpls-resolution 306
- 16.44 neighbor activate 307
- 16.51 neighbor description 311
- 16.53 neighbor ebgp-multihop 313
- 16.54 neighbor filter-list 313
- 16.56 neighbor next-hop-self 315
- 16.58 neighbor passive 316
- 16.61 neighbor prefix-list 318
- 16.62 neighbor remote-as 319
- 16.66 neighbor shutdown 322
- 16.69 neighbor timers 324
- 16.71 neighbor update-source 325
- 16.72 neighbor version 326
- 16.73 neighbor weight 327
- 16.74 network 328
- 16.76 synchronization 329
- 16.77 router bgp 330
- 16.78 show debugging bgp 331
- 16.79 show ip bgp 331
- 16.81 show ip bgp cidr-only 332
- 16.82 show ip bgp community 333
- 16.85 show ip bgp dampening 334
- 16.88 show ip bgp neighbors 336
- AF-dependant capabilities: 337
- 16.89 show ip bgp paths 338
- 16.92 show ip bgp regexp 339
- 16.93 show ip bgp scan 340
- 16.94 show ip bgp summary 340
- 16.95 show ip bgp view 341
- 16.98 show ip bgp vpnv4 343
- 16.100 show ip protocols 344
- 16.101 timers 345
- 16.102 undebug bgp 346
- 17 VRRP Commands 347
- 17.2 authentication mode 348
- 17.3 interface (VRRP) 348
- 17.4 preempt-mode 349
- 17.5 priority (VRRP) 350
- 17.6 router vrrp 351
- 17.7 track (VRRP) 351
- 17.8 virtual-ip 352
- 17.9 show vrrp 353
- 18.1 IP SLA MONITOR 355
- 18.3 FREQUENCY 356
- 18.4 TIMEOUT 357
- 18.5 THRESHOLD 357
- 18.6 VRF 358
- 18.7 IP SLA MONITOR SCHEDULE 359
- 18.8 SHOW IP SLA MONITOR 359
- 18.10 TRACK RTR REACHABILITY 361
- 18.11 TRACK RTR STATE 362
- 18.12 TRACK 363
- 18.13 DELAY UP 363
- 18.14 DELAY DOWN 364
- 18.15 SHOW TRACK 365
- 18.16 TRACK 365
- 18.17 SHOW VRRP 366
- 18.17.1.6 Related Commands 367
- 19 Route-map Commands 368
- 19.1.1.4 Defaults 369
- 19.1.1.5 Examples 369
- 19.1.1.6 Related Commands 369
- 19.3.1.1 Command Syntax 371
- 19.3.1.2 Syntax Description 371
- 19.3.1.3 Command Mode 371
- 19.3.1.4 Defaults 371
- 19.3.1.5 Examples 371
- 19.4 match interface 372
- 19.4.1.6 Related Commands 373
- 19.5.1.1 Command Syntax 373
- 19.5.1.2 Syntax Description 373
- 19.5.1.3 Command Mode 373
- 19.5.1.4 Defaults 373
- 19.5.1.5 Examples 374
- 19.5.1.6 Related Commands 374
- 19.6.1.1 Command Syntax 374
- 19.6.1.2 Syntax Description 374
- 19.6.1.3 Command Mode 375
- 19.6.1.4 Defaults 375
- 19.6.1.5 Examples 375
- 19.6.1.6 Related Commands 375
- 19.9 match local-preference 377
- 19.9.1.2 Syntax Description 378
- 19.9.1.3 Command Mode 378
- 19.9.1.4 Defaults 378
- 19.9.1.5 Examples 378
- 19.9.1.6 Related Commands 378
- 19.11 match origin 379
- 19.12 match route-type 381
- 19.13 match tag 382
- 19.14.1.1 Command Syntax 383
- 19.14.1.2 Syntax Description 383
- 19.14.1.3 Command Mode 383
- 19.14.1.4 Defaults 383
- 19.14.1.5 Examples 384
- 19.14.1.6 Related Commands 384
- 19.15.1.1 Command Syntax 384
- 19.15.1.2 Syntax Description 384
- 19.16 set atomic-aggregate 385
- 19.17 set comm-list delete 386
- 19.17.1.4 Defaults 387
- 19.17.1.5 Examples 387
- 19.17.1.6 Related Commands 387
- 19.18.1.1 Command Syntax 387
- 19.18.1.2 Syntax Description 387
- 19.18.1.3 Command Mode 388
- 19.18.1.4 Defaults 388
- 19.18.1.5 Examples 388
- 19.18.1.6 Related Commands 388
- 19.19.1.1 Command Syntax 389
- 19.19.1.2 Syntax Description 389
- 19.19.1.3 Command Mode 389
- 19.19.1.4 Defaults 389
- 19.19.1.5 Examples 389
- 19.20 set extcommunity 390
- 19.20.1.6 Related Commands 391
- 19.21.1.1 Command Syntax 391
- 19.21.1.2 Syntax Description 391
- 19.21.1.3 Command Mode 391
- 19.21.1.4 Defaults 391
- 19.22 set local-preference 392
- 19.22.1.6 Related Commands 393
- 19.23.1.1 Command Syntax 393
- 19.23.1.2 Syntax Description 393
- 19.23.1.3 Command Mode 393
- 19.23.1.4 Defaults 393
- 19.24 set metric-type 394
- 19.24.1.6 Related Commands 395
- 19.25.1.1 Command Syntax 395
- 19.25.1.2 Syntax Description 395
- 19.25.1.3 Command Mode 395
- 19.26 set originator-id 396
- 19.27 set tag 397
- 19.27.1.4 Defaults 398
- 19.27.1.5 Examples 398
- 19.27.1.6 Related Commands 398
- 19.28.1.1 Command Syntax 398
- 19.28.1.2 Syntax Description 398
- 19.28.1.3 Command Mode 399
- 19.28.1.4 Defaults 399
- 19.28.1.5 Examples 399
- 19.28.1.6 Related Commands 399
- 19.30 show route-map 400
- 19.30.1.4 Examples 401
- 19.30.1.5 Related Commands 401
- VRF Commands 402
- 20.2 show ip vrf 403
- 20.4 ip route vrf 404
- 20.5 arp vrf 405
- 20.6 show ip arp vrf 406
- 20.7 clear ip arp vrf 406
- 20.8 ping vrf 407
- 20.9 traceroute vrf 408
- 21 IGMP Commands 409
- 21.5 ip igmp limit 411
- 21.6 ip igmp mroute-proxy 412
- 21.7 ip igmp proxy-service 413
- 21.12 ip igmp version 416
- 21.14 ip multicast-routing 417
- 21.15 show ip igmp groups 418
- 21.16 show ip igmp interface 418
- 21.17 show ip mroute 419
- 21.18 show ip mroute-rpf 420
- 22 IGMP Snooping Commands 422
- 22.10 ip igmp snooping vlan 427
- 22.11 show ip igmp snooping 428
- 23 MVR Commands 432
- 23.3 mvr group 433
- 23.4 mvr source-address 433
- 23.5 mvr type 434
- 23.6 show mvr 435
- 23.7 show mvr interface 435
- 23.8 show mvr group 436
- 23.9 show mvr group static 436
- 24 PIM Commands 438
- 24.3 ip pim bsr-candidate 439
- 24.4 ip pim bsr-border 440
- 24.5 ip pim dr-priority 440
- 24.6 ip pim exclude-genid 441
- 24.7 ip pim hello-interval 441
- 24.9 ip pim jp-timer 443
- 24.15 ip pim rp-address 447
- 24.16 ip pim rp-candidate 447
- 24.20 ip pim sparse-mode 450
- 24.21 ip pim unicast-bsm 450
- 25 LDP Commnands 456
- 25.2 clear ldp adjacency 457
- 25.3 clear ldp session 458
- 25.4 clear ldp statistics 459
- 25.6 control-mode 461
- 25.8 debug ldp all 464
- 25.9 debug ldp dsm 465
- 25.10 debug ldp events 466
- 25.11 debug ldp fsm 468
- Syntax Description 470
- 25.13 debug ldp packet 471
- 25.14 debug ldp qos 473
- 25.15 debug ldp tsm 474
- 25.16 debug ldp vc 475
- 25.17 disable-ldp 476
- 25.18 enable-ldp 477
- 25.19 explicit-null 478
- 25.20 hello-interval 479
- 25.22 keepalive-interval 481
- 25.23 keepalive-timeout 482
- 25.24 ldp hello-interval 483
- 25.25 ldp hold-time 484
- 25.26 ldp keepalive-interval 485
- 25.27 ldp keepalive-timeout 486
- 25.28 ldp multicast-hellos 487
- 25.31 router ldp 490
- 25.32 router-id 491
- 25.33 show debugging ldp 492
- 25.34 show ldp 493
- 25.35 show ldp adjacency 494
- 25.37 show ldp downstream 496
- 25.38 show ldp fec 498
- 25.39 show ldp interface 499
- 25.40 show ldp lsp 500
- 25.42 show ldp session 503
- 25.43 show ldp statistics 505
- 25.45 show ldp upstream 508
- 25.46 show memory ldp 510
- 25.47 targeted-peer 512
- number 513
- 25.51 transport-address 516
- 25.52 show ldp vpls 517
- 26 MPLS Commands 518
- 26.2 no mpls ilm-entry 519
- 26.3 mpls ftn-entry 520
- 26.4 no mpls ftn-entry 521
- 26.5 mpls lsp-tunneling 522
- 26.6 no mpls lsp-tunneling 523
- 26.7 mpls map-route 524
- 26.8 no mpls map-route 525
- Switch# configure terminal 526
- 26.11 label-switching 527
- 26.13 show mpls ftn-database 530
- 26.15 show mpls ilm-database 531
- 26.17 show mpls interface 533
- 26.20 show mpls statistics 536
- 26.21 show mpls 537
- 26.22 clear mpls statistics 538
- 27 BGP VPN Commands 540
- 27.3 debug bgp mpls 541
- 27.4 exit-address-family 542
- 27.5 neighbor activate 542
- 27.6 neighbor allowas-in 543
- 27.8 neighbor as-override 544
- 27.9 neighbor description 545
- 27.10 neighbor remote-as 546
- 27.12 neighbor shutdown 547
- 27.13 neighbor soo 548
- 27.14 redistribute 548
- 27.15 route distinguisher 549
- 27.16 route-target 549
- 27.18 show ip vrf 551
- 28 Route-map Commands 553
- 28.1.1.4 Defaults 554
- 28.1.1.5 Examples 554
- 28.1.1.6 Related Commands 554
- 28.3.1.1 Command Syntax 556
- 28.3.1.2 Syntax Description 556
- 28.3.1.3 Command Mode 556
- 28.3.1.4 Defaults 556
- 28.3.1.5 Examples 556
- 28.4 match interface 557
- 28.4.1.6 Related Commands 558
- 28.5.1.1 Command Syntax 558
- 28.5.1.2 Syntax Description 558
- 28.5.1.3 Command Mode 558
- 28.5.1.4 Defaults 558
- 28.5.1.5 Examples 559
- 28.5.1.6 Related Commands 559
- 28.6.1.1 Command Syntax 559
- 28.6.1.2 Syntax Description 559
- 28.6.1.3 Command Mode 560
- 28.6.1.4 Defaults 560
- 28.6.1.5 Examples 560
- 28.6.1.6 Related Commands 560
- 28.9 match local-preference 562
- 28.9.1.2 Syntax Description 563
- 28.9.1.3 Command Mode 563
- 28.9.1.4 Defaults 563
- 28.9.1.5 Examples 563
- 28.9.1.6 Related Commands 563
- 28.11 match origin 564
- 28.12 match route-type 566
- 28.13 match tag 567
- 28.14.1.1 Command Syntax 568
- 28.14.1.2 Syntax Description 568
- 28.14.1.3 Command Mode 568
- 28.14.1.4 Defaults 568
- 28.14.1.5 Examples 569
- 28.14.1.6 Related Commands 569
- 28.15.1.1 Command Syntax 569
- 28.15.1.2 Syntax Description 569
- 28.16 set atomic-aggregate 570
- 28.17 set comm-list delete 571
- 28.17.1.4 Defaults 572
- 28.17.1.5 Examples 572
- 28.17.1.6 Related Commands 572
- 28.18.1.1 Command Syntax 572
- 28.18.1.2 Syntax Description 572
- 28.18.1.3 Command Mode 573
- 28.18.1.4 Defaults 573
- 28.18.1.5 Examples 573
- 28.18.1.6 Related Commands 573
- 28.19.1.1 Command Syntax 574
- 28.19.1.2 Syntax Description 574
- 28.19.1.3 Command Mode 574
- 28.19.1.4 Defaults 574
- 28.19.1.5 Examples 574
- 28.20 set extcommunity 575
- 28.20.1.6 Related Commands 576
- 28.21.1.1 Command Syntax 576
- 28.21.1.2 Syntax Description 576
- 28.21.1.3 Command Mode 576
- 28.21.1.4 Defaults 576
- 28.22 set local-preference 577
- 28.22.1.6 Related Commands 578
- 28.23.1.1 Command Syntax 578
- 28.23.1.2 Syntax Description 578
- 28.23.1.3 Command Mode 578
- 28.23.1.4 Defaults 578
- 28.24 set metric-type 579
- 28.24.1.6 Related Commands 580
- 28.25.1.1 Command Syntax 580
- 28.25.1.2 Syntax Description 580
- 28.25.1.3 Command Mode 580
- 28.26 set originator-id 581
- 28.27 set tag 582
- 28.27.1.4 Defaults 583
- 28.27.1.5 Examples 583
- 28.27.1.6 Related Commands 583
- 28.28.1.1 Command Syntax 583
- 28.28.1.2 Syntax Description 583
- 28.28.1.3 Command Mode 584
- 28.28.1.4 Defaults 584
- 28.28.1.5 Examples 584
- 28.28.1.6 Related Commands 584
- 28.30 show route-map 585
- 28.30.1.4 Examples 586
- 28.30.1.5 Related Commands 586
- 29 VPWS Commands 587
- 29.2 no mpls l2-circuit 588
- 29.3 mpls-l2-circuit 589
- 29.4 no mpls-l2-circuit 590
- 29.7 show mpls l2-circuit 593
- 29.8 show mpls vc-table 594
- 30 VPLS Commands 595
- 30.2 no mpls vpls-vlan 596
- 30.3 mpls vpls 597
- 30.4 no mpls vpls 598
- 30.5 vpls-description 599
- 30.6 no vpls-description 600
- 30.7 vpls-mtu 601
- 30.8 no vpls-mtu 602
- 30.9 vpls-peer 603
- 30.10 no vpls-peer 604
- 30.11 vpls-fib-add 605
- 30.12 vpls-fib-delete 606
- 30.13 mpls-vpls 607
- 30.14 no mpls-vpls 608
- 30.16 show mpls vpls 610
- 31 MPLS OAM Commnands 613
- 31.2 ping mpls l2-circuit 615
- 31.3 ping mpls l3vpn 617
- 31.4 traceroute mpls ipv4 619
- 31.6 traceroute mpls l3vpn 623
- 32 QoS Commands 625
- 32.3 qos map cos-pri-color 627
- 32.4 qos map exp-pri-color 628
- 32.6 qos map pri-color-cos 629
- 32.7 qos map pri-color-dscp 630
- 32.8 qos map pri-color-exp 631
- 32.9 show qos map-table all 632
- 32.12 cos 634
- 32.13 trust dscp 635
- 32.14 trust ip-prec 635
- 32.15 trust outer 636
- 32.16 trust port 636
- 32.17 trust cos 637
- 32.18 replace cos 637
- 32.19 replace dscp 638
- 32.20 queue class 639
- 32.21 queue random-detect 639
- (drop-probability)/256 640
- 32.25 queue threshold 643
- 32.26 queue-bandwidth 643
- 32.27 qos statistics queue 644
- 32.29 shape average percent 645
- 32.30 queue shape 646
- 32.31 aggregate-policer 646
- 32.32 class-map 647
- 32.33 match access-group 648
- 32.34 policy-map 648
- 32.35 class NAME 649
- 32.36 trust 650
- 32.37 set priority color 650
- 32.38 policer 651
- 32.39 policer-aggregate 652
- 32.40 port-policing 652
- 32.41 service-policy 653
- 32.43 qos statistics policer 654
- 32.48 show policy-map 657
- 32.51 show class-map 659
- 33 ACL Commands 662
- 33.3 permit 663
- 33.4 no sequence-num 664
- 33.5 show access-list arp 664
- 33.6 mac access-list 665
- 33.7 exit 666
- 33.8 no sequence-num 666
- 33.11 remark 669
- 33.12 mac access-group 669
- 33.13 show access-list mac 670
- 33.15 ip access-list 671
- 33.16 exit 672
- 33.17 no sequence-num 672
- 33.18 deny 673
- 33.20 deny udp 675
- 33.21 deny icmp 676
- 33.22 deny igmp 677
- 33.23 permit 677
- 33.25 permit udp 680
- 33.26 permit icmp 681
- 33.27 permit igmp 681
- 33.28 remark 682
- 33.29 ip access-group 683
- 33.30 show access-list ip 683
- 33.31 time-range 684
- 33.32 absolute 685
- 33.33 periodic 685
- 33.34 show time-range 686
- 34 ARP Inspection Commands 687
- 34.4 ip arp inspection trust 690
- 34.6 ip arp inspection vlan 692
- 34.8 show ip arp inspection 694
- 35 IP Source Guard Commands 696
- 35.3 ip verify source 697
- 36 DHCP Snooping Commands 699
- 36.3 dhcp snooping binding 700
- 36.4 dhcp snooping database 701
- 36.7 dhcp snooping trust 704
- 36.8 dhcp snooping verify 704
- 36.9 dhcp snooping vlan 705
- 37 IEEE 802.1x Commands 709
- 37.3 dot1x port-control 710
- 37.4 dot1x protocol-version 711
- 37.5 dot1x quiet-period 712
- 37.6 dot1x reauthentication 712
- 37.7 dot1x re-authenticae 713
- 37.8 dot1x timeout 713
- 37.9 radius deadtime 715
- 37.10 radius-server host 715
- 37.11 radius retransmit 717
- 37.12 radius timeout 717
- 37.13 show dot1x 718
- 38.1 aaa new-model 720
- 38.2 no aaa new-model 720
- 38.8 show aaa status 724
- 39 File Operation Commands 726
- 39.3 delete 727
- 39.4 dir 728
- 39.5 ls 729
- 39.6 more 730
- 39.7 mkdir 731
- 39.8 rename 731
- 39.9 rmdir 732
- 39.10 tar create 733
- 39.11 tar table 733
- 39.12 tar xtract 734
- 39.13 copy running-config 734
- 39.14 copy startup-config 735
- 39.15 copy tftp:// 736
- 39.16 show running-config 736
- 39.17 show startup-config 738
- 39.18 write 739
- 39.19 write memory 739
- 39.20 write terminal 739
- 39.21 ftp 740
- 39.22 ftp username 741
- 39.23 ftp password 741
- 39.24 ftp passive 742
- 39.25 show ftp 743
- 40.1 ip ssh server 744
- 40.7 ip ssh server version 748
- 40.10 rsa key 750
- 40.11 key format 750
- 40.12 key string end 751
- 40.13 key type 751
- 40.14 reset 752
- 40.15 validate 752
- 40.16 KEYLINE 753
- 40.17 rsa key export 754
- 40.18 rsa key import 754
- 40.19 show rsa key 755
- 40.20 show rsa keys 756
- 40.21 clock set datetime 756
- 40.22 clock set timezone 757
- 40.23 clock set summertime 758
- 40.24 show clock 759
- 40.25 ntp ace 760
- 40.26 ntp authentication 761
- 40.27 ntp broadcast client 762
- 40.28 ntp key 762
- 40.29 ntp interface reload 763
- 40.30 ntp peer 763
- 40.31 ntp refclock 764
- 40.32 ntp server 765
- 40.33 ntp trustedkey 766
- 40.34 show ntp 767
- 40.35 show ntp association 767
- 40.36 show ntp key 768
- 40.37 show ntp status 769
- 40.38 show ntp statistics 769
- 40.41 show memory 773
- 40.42 show network services 775
- 40.45 show file system 779
- 40.46 debug arp 779
- 40.47 debug dhcp relay 780
- 40.48 debug dhcp snooping 781
- 40.49 debug igmp 781
- 40.50 debug stp 782
- 40.51 debug ospf 783
- 40.52 debug pim sparse-mode 784
- 40.53 show debugging 784
- 40.54 ping 785
- 40.55 traceroute 786
- 40.56 boot system 787
- 40.57 reload 787
- 40.58 schedule reboot at 788
- 40.59 schedule reboot delay 788
- 40.60 show boot 789
- 40.61 show boot images 790
- 40.62 clear logging buffer 790
- 40.63 logging alarm-trap 791
- 40.64 logging file 792
- 40.65 logging level file 792
- 40.66 logging level module 793
- 40.67 logging merge 794
- 40.68 logging operate 795
- 40.69 logging server 795
- 40.73 logging timestamp 799
- 40.74 show logging 799
- 40.75 show logging buffer 800
- 40.76 show history 801
- 40.77 clear line vty 802
- 40.78 re-username 802
- 40.79 username 803
- 40.80 show users 804
- 40.81 show usernames 805
- 40.87 show mac address-table 809
- 41 Mirror Commands 812
- 41.4 show monitor 814
- 42 DHCP Relay Commands 815
- 42.3 dhcp-server (interface) 816
- 42.9 serveice dhcp 821
- 42.10 show dhcp-server 821
- 43 DNS Commands 826
- 43.3 dns server 827
- 43.4 show dns 828
- 43.5 show ip host 828
- 44 SNMP Commands 830
- 44.2 snmp-server community 831
- 44.3 snmp-server context 831
- 44.4 snmp-server enable 832
- 44.5 snmp-server engineID 833
- 44.6 snmp-server group 833
- 44.7 snmp-server notify 834
- 44.12 snmp-server usm-user 838
- 44.13 snmp-server version 839
- 44.14 snmp-server view 839
- 44.19 show snmp-server group 843
- 44.25 show snmp-server view 846
- 45 Sflow Commands 848
- 45.3 sflow counter interval 849
- 45.4 sflow counter enable 849
- 45.5 sflow sample rate 850
- 45.6 sFlow sample enable 851
- 45.7 show sflow 852
- 45.8 debug sflow 853
- 45.9 show debugging sflow 853
Relacionado con productos y manuales para Hardware De La Computadora Canoga-perkins CanogaOS Command Reference
(350 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.074 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales