Canoga-perkins 9151 Network Interface Device Manual de usuario Pagina 1

9151 Network Interface Device User Manual

4. Install the interface modules in the single port slots: a. Insert a module into a slot and push firmly on the center of the front panel. If it d

The LEDs on the front panel show the system and port conditions. The STA and CFG LEDs show the management conditions; see Table 1. Each interface mo

LED Status Description SPD Off 10BaseT data rate Amber 100BaseT data rate or system self-test Green 1000BaseT data rate Alarms The 9151 can g

Link Loss Forwarding When LLF is enabled, a fault on one side of the 9151 propagates to the other side to notify that device and stops signal transmis

9151 Network Interface Device 2-6

Chapter 3 Using the Software You can manage the system through VT100 Terminal Emulation, which is accessible by a Telnet session, HyperTerminal or si

Set Up the PC for Terminal Operation These steps briefly describe how to set up your PC for a terminal connection. For details on using Windows, see

Messages andurgent statusScreen navigationinstructionsChange optionsStatus reportsModel number Figure 4. General Screen Format Not all screens and me

Main Menu 1) System 1) System Information 2) Module Information 3) IP Settings 8) Static ARP Table 4) Host Access Table

Login and the 9151 Main Menu The first screen is the Login. If this is your initial setup and no user name or password has been set, type admin and p

2. At the System Information screen, type the number for an item and press <Enter>, then type the information and press <Enter>. • 1. Sy

2. At the SNTP Client Configuration screen, type the number for a parameter and press <Enter>, then follow the prompts on the screen. • 1. SNT

2. At the Host Access Table screen, type 2 to add a host, then at the prompt, enter the host IP address and mask, or type 1 to edit a host. At the A

3. To return to the System menu, press <Esc>. These selections do not affect how the Major and Minor LEDs report alarms. Table 4. Trap Configu

Update Software Each 9151 has two flash memory banks that store software: • The Active Flash Memory holds the software currently in use • The Inacti

Set General Security Parameters General security parameters include values for passwords, lockout, and logout, which are basic to maintaining security

Set Up User Accounts You can set up an account for a user, whether another supervisor, operator, or observer, to access the 9151. You can also update

4. To delete a user, type 3, then follow the prompts to select the user name and confirm the choice; the User Accounts screen reappears. 5. To retur

Set Up the Notification Destination for Traps Use the Trap Notification/Destination Table to view and set up the destination for Trap messages. In ad

• Privacy Password: If the privacy protocol is DES, enter the password that generates the encryption key for the message; 8 to 15 characters • Priv

CAUTION! This product may contain a laser diode operating at a wavelength of 1300 nm - 1600 nm. Use of optical instruments (e.g., collimating optics)

Ethernet bridges or switches use the Spanning Tree Protocol (STP), an algorithm that creates a logical topology that connects all network segments and

When setting up ports in the various switch configuration options, including for LAGs and double tagging, set up and configure options in this order o

Check and Update Port Information The Port Information screen shows the current conditions for all ports in the 9151 with options to view parameters a

• 3. Configuration Name: Name for configuration, typically MAC address, up to 32 characters • 4. Configuration Revision: Set a revision level betw

3. To add a port, type 5, "Add Port," or to delete a port, type 6, "Delete Port," then at the prompt, type the port name and pres

• 6. Ingress Filter: Enable, filter out received frames that are not for this VLAN, or Disabled, forward all received frames. • 7. PVID: Enter the

Set Up Multiple Spanning Tree Parameters Use the Multiple Spanning Tree (MST) Instance Configuration screen to view and set up instances of grouped or

Check LAG Data You can check the status for each LAG and view statistics about activity on each LAG. The Lag Configuration screen shows when the lat

To access these screens, follow these steps: 1. From the Switch Configuration menu, type 4, "Lag Configuration," and press <Enter>. 2

Chapter 4 Maintenance and Troubleshooting General Maintenance and Managing Cable Links Well-maintained components and clearly identified cables help

NOTICE Canoga Perkins has prepared this users manual for use by customers and Canoga Perkins personnel as a guide for the proper installation, operati

Measure Transmitter Output Power To measure the output power, follow these steps: 1. Clean the connectors on the fiber optic test cable, then plug it

Measure Fiber Link Attenuation Determine and record link attenuation before starting normal link traffic. The attenuation factor identifies potential

New Installation On new installations, make sure that all steps in Chapter 2 are complete, then follow these steps: 1. Check that the STA LED is gree

Test a Connection With PING When you set up a new connection or need to troubleshoot an existing connection to another device, you can send a PING to

9151 Network Interface Device 4-6

Chapter 5 Specifications 9151 Specifications Standards: IEEE 802.3 Dimensions: 1.72" H x 13.375" W x 17.25" D (44 x 340 x 438 mm) Wei

9151 Interface Model Numbers Model Description 10/100/1000 Mbps UTP Interface 9501-330 10/100/1000 BASE TX UTP 10 Mbps Optical Interfaces 9501-431 1

Appendix A Warranty Limited Lifetime Warranty Effective July 1, 2005 and After, Canoga Perkins warrants that, at the time of sale, and, for its lifeti

Limitations Canoga Perkins may at its sole discretion modify its Limited Warranty at any time and from time to time. Other than those expressly stated

Appendix B Acronym and Abbreviation List FPGA Field Programmable Gate Array GARP General Attributes Registration Protocol for registering a client s

Table of Contents Chapter 1 Overview...1-1 Chapter 2 Ha

9151 Network Interface Device B-2

Index A I add input/output options, 1-1 trap destination, 3-14 install hardware, 2-1 user account, 3-12 IP address Host Access Table, 3-7 C latenc

S security general parameters, 3-11 screen lockout, 3-11 Connected Sessions, 3-13 logout, 3-11 Description Report, 3-6 password characteristics, 3-11

U User Accounts screen, 3-12, 3-13 user interface organization, 3-3 UTP/optical options, 1-1 V VLAN Configuration screen, 3-20 VLANx Information scree

CANOGA PERKINS CORPORATION 20600 Prairie Street Chatsworth, California 91311-6008 USA Phone: (818) 718-6300 FAX: (818) 718-6312 Web Site:

Check the Forwarding Database... 3-24 Check the Static an

Chapter 1 Overview The 9151 is a Four-Port Aggregator Network Interface Device that provides intelligent optical demarcation and terminates managed t

9151 Network Interface Device 1-2

Chapter 2 Hardware Installation and Functions This chapter describes how to set up and install the 9151 and the interface modules as well as the hard