Canoga-perkins 9160 10 Gigabit Ethernet Network Interface Device Manual de usuario

9160 10 Gigabit Ethernet Network Interface Device User Manual

Set-up and Installation This section describes how to set up and install the 9160. Before setting up the 9160, make sure the serial cable (require

Dirty optical connectors are a common cause of link loss or attenuation problems, especially for SMF. Clean the connectors before plugging in a cabl

LED Status Description MGR Off No power Green Normal operation Green blinking Management traffic Amber System self-test or over-temperature tra

2-4 9160 10 Gigabit Ethernet Network Interface Device Remote Fault The 9160 supports Remote Fault (RMTF) on all MP and SP optical ports with speeds

Using the Software You can manage the system through VT100 Terminal Emulation, which is accessible by a Telnet session, HyperTerminal or similar te

Set Up the PC for Terminal Operation These steps briefly describe how to set up your PC for a terminal connection. For details on using Windows, see

Messages andurgent statusScreen navigationinstructionsChange optionsStatus reportsModel number Figure 3. General Screen Format Not all screens and m

User Interface Organization The user interface consists of selectable, nested screens, described in this chapter and available in this order: Main Me

Login and the Main Menu The first screen is the Login. If this is your initial setup and no user name or password has been set, type admin and press

2. At the System Information screen, type the number for an item and press <Enter>, then type the information and press <Enter>. • Syst

Manage the Date and Time An accurate date and time in the 9160 assures accuracy for events listed in the System Log and for traps and alarms sent to

2. At the IP Settings screen, type the number for an item and press <Enter>, then enter data or press <Space> to cycle through the optio

Table 4. Trap Configuration Options Trap When enabled, sends a Trap if. . . Cold Start The 9160 is reset by a power failure or forced reset Remote

Update Software Each 9160 has two flash memory banks that store software: • The Active Flash Memory holds the software currently in use • The Inact

Set General Security Parameters General security parameters include values for passwords, lockout, and logout, which are basic to maintaining securit

Set Up User Accounts You can set up an account for a user, whether another supervisor, operator, or observer, to access the 9160. You can also updat

4. To delete a user, type 3, then follow the prompts to select the user name and confirm the choice; the User Accounts screen reappears. 5. To retu

Set Up Host Access The SNMP agent allows access to up to 24 Host IP addresses. Set up and edit the Host information for the 9160 at the Host Access

3. To finish setting up V1-Trap, V2-Trap, or V2c-Inform notification, type the community name, up to 10 characters, and press <Enter>. 4. To

NOTICE Canoga Perkins has prepared this users manual for use by customers and Canoga Perkins personnel as a guide for the proper installation, opera

Managing the Network Interface The Switch Configuration menu offers options to set network parameters; see Table 5. Table 5. Network Spanning Tree P

When setting up ports in the various switch configuration options, set up options in this order: 1. Set up the physical layer, such as port speeds.

2. At the Global Spanning Tree Parameters menu, type the number for an item and press <Enter>, then follow the prompts to set values for these

Set Up VLANs Use the VLAN Configuration screen to view and set VLAN parameters for the 9160. To access the VLAN Configuration screen, follow these s

3-20 9160 10 Gigabit Ethernet Network Interface Device Set Up Optional Double Tagging If you are using the 9160 within a service provider environmen

Check the Forwarding Database To view the listings of VLAN ID, MAC address, port name, and status in the Forwarding database (Fdb log), follow these

Maintenance and Troubleshooting General Maintenance and Managing Cable Links Well-maintained components and clearly identified cables help assure o

Measure Transmitter Output Power To measure the output power, follow these steps: 1. Clean the connectors on the fiber optic test cable, then plug i

Measure Fiber Link Attenuation Determine and record link attenuation before starting normal link traffic. The attenuation factor identifies potentia

4-4 9160 10 Gigabit Ethernet Network Interface Device New Installation On new installations, make sure that all steps in Chapter 2 are complete, th

Test a Connection With PING When you set up a new connection or need to troubleshoot an existing connection to another device, you can send a PING to

Specifications See also the specifications for the chassis or standalone enclosure. 9160 Specifications Standards: IEEE 802.3 Dimensions: 2.625&qu

5-2 9160 10 Gigabit Ethernet Network Interface Device 9160 Interface Model Numbers Model Description Interface Modules 10/100/1000 Mbps UTP Interfac

10GigE XFP Modules XFP1-0265 10 GBase-SR 850nm MM 300m LC XFP1-2265 10 GBase-LR 1310nm SM 10km LC XFP1-3465 10 GBase-ER 1550nm SM 40km LC XFP1-36

9160 10 Gigabit Ethernet Network Interface Device A-1 Warranty Information Current Warranty information is available on-line in the Client Logi

9160 10 Gigabit Ethernet Network Interface Device B-1/(B-2 Blank) Acronym and Abbreviation List FPGA Field Programmable Gate Array LAG Link Ag

CAUTION! This product may contain a laser diode operating at a wavelength of 1300 nm - 1600 nm. Use of optical instruments (e.g., collimating optics

CANOGA PERKINS CORPORATION 20600 Prairie Street Chatsworth, California 91311-6008 USA Phone: (818) 718-6300 FAX: (818) 718-6312 Web Site:

Table of Contents Overview ...1-1 S

ii 9160 10 Gigabit Ethernet Network Interface Device General Maintenance and Managing Cable Links.....

Overview The 9160 10 Gbps Ethernet Network Interface Device that provides intelligent optical demarcation and terminates managed transport at the p