Canoga-perkins 9145E Network Interface Device Software Version 2. Manual de usuario Pagina 51
- Pagina / 112
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Diagnostics 9145E NID Software User’s Manual
VLAN Loopback
43
4.4.2 L2 Ping Generator
To set up the L2 Ping generator, type 3 and press Enter. The L2 Ping Generator screen (Figure 4-9)
appears.
Figure 4-9 802.1ag Loopback Configuration
Run the test by selecting 13. This will give you all the statistics that are described below.
Destination MAC Address: MAC address that the LBMs will be sent to.
VLAN ID: - VLAN ID to be put in the LBM.
VLAN Priority: - Priority to be put in VLAN tag.
Ethertype: - Ethertype to be put in the LBM.
MD Level: - MD level to be put in the LBM.
Egress Port: - Port that the LBMs will be sent out.
Frame Count: - Number of LBMs to be sent out.
Frame Size: - Frame size of the LBM to be built, excluding 4 bytes CRC.
Frame Interval: - Time interval between two LBMs to be sent out. 0-500 in 10 ms intervals may be
specified. 0 indicates as fast as possible.
Frame Format: - Frame to be sent out in IEEE 802.3 or LLC SNAP format.
Start L2 Ping: - Start to send out the LBM and verify the responses. The status will be shown. You
may stop the testing by entering the ESC key.
After starting a Layer 2 Ping, the following statistics will appear on the bottom half of the screen:
First Transaction ID: - Transaction identifier for the first LBM sent out in this test.
LBM Transmitted: - Number of LBMs sent out in this test.
LBR Received: - Number of valid LBRs been received in this test.
Can og a Perkins Corp Ethernet Netw ork Interface D evice 22 -SEP-2008
M odel 9145E-101-2-0 V 02.10 F121 02 :59:35
-------------------------------L2 PING GENERATOR--------------------------------
1) D estination M A C A ddress 00 -00-00-00-00-00
2) V L A N ID (1-4 09 4) 1
3) V L A N Priority (0 -7) 0
4) E thertype (4 Hex digits) 8902
5) M D Lev el (0-7) 7
6) E gress Port Net
7) Frame Count (1-99999999) 1
8) M inim um Fram e S ize (60-9996) 60
9) M axim um F ram e Size (60-9996) 1514
10) Increm ental Size (0-256) 0
11) Frame Time Interval (0-5 00 1 0m s) 0
12) Frame Format IEEE 802.3
13) Start L2 Ping
------------------------------------M essages------------------------------------
- Software Version 2.1 1
- User’s Manual 1
- Table of Contents 3
- About this Manual 7
- How this Manual is Organized 7
- What is New in This Document 7
- Optional Applications 8
- Contacting Technical Support 8
- Document Feedback 8
- Chapter 1 9
- Introduction 9
- 1.3 Three Levels of Security 10
- Chapter 2 11
- Getting Started 11
- 2.1.1 About MIBs 12
- 2.1.2 9145E Set-up 12
- 2.3 Login 14
- 2.4 Main Menu 15
- 2.5 Supported MIBs 16
- Chapter 3 17
- System Configuration 17
- 3.1.3 Host Table 21
- 3.1.4 Trap Table 23
- 3.2 Trap Configuration 27
- Trap Configuration 29
- 3.3 Security Configuration 30
- 3.4 Account Configuration 32
- 3.4.2 Add or Edit an Account 33
- NOTE: SNMP only cannot FTP 34
- 3.5 System Information 35
- 3.9 Hardware Information 41
- Chapter 4 43
- Diagnostics 43
- 4.1 Loopback Setup 44
- 4.2 Latency/Jitter Test 44
- 4.3 PING Generation 47
- 4.4 VLAN Loopback 48
- Figure 4-6 VLAN Loopback 49
- 4.4.2 L2 Ping Generator 51
- 4.5 Cable Diagnostics 52
- Chapter 5 53
- Port Information 53
- 5.1 Link Status 54
- 5.2 Port Configuration 54
- 5.2.1 Hardware Information 55
- 5.2.3 VLAN Configuration 58
- 5.2.4 Port Filters 61
- 5.3 Layer 2 Statistics 64
- Layer 2 Statistics 65
- 5.4 RMON Group 1 Statistics 67
- 61/(62 Blank) 69
- Chapter 6 71
- System Alarms & Logs 71
- 6.1 System Log 72
- 65/(66 Blank) 73
- Chapter 7 75
- Utilities 75
- 7.3 Change Password 76
- 7.4 VT100 Baud Rate 76
- 7.5 PING Generation 76
- 7.6 Static ARP Table 77
- 7.7 Dynamic ARP Table 78
- 7.8 License Manager 78
- 71/(72 Blank) 79
- Chapter 8 81
- Software Upgrade 81
- 77/(78 Blank) 85
- Chapter 9 87
- 802.3AH OAM 87
- 9.1 OAM Control 88
- 9.2 OAM Peer Information 90
- 9.3 OAM Statistics 91
- 9.4 OAM Event Configuration 92
- 9.5 OAM Event Log 92
- OAM Event Log 93
- 87/(88 Blank) 95
- Chapter 10 97
- Class of Service 97
- Configuration 97
- 10.1 CoS Support 98
- 10.2 Classifier Mapping 98
- 10.2.3.2 DSCP Mode 101
- Enter. The cursor 101
- 10.3 Queue Configuration 102
- 10.3.3 Scheduling Scheme 103
- 10.3.4 Weight Parameters 104
- 10.5 Queue Statistics 107
- Appendix A 109
- Acronyms 109
- CANOGA PERKINS CORPORATION 112
Relacionado con productos y manuales para Hardware De La Computadora Canoga-perkins 9145E Network Interface Device Software Version 2.
Hardware De La Computadora Canoga-perkins 9145E Standard NID Software Version 1.0 Manual de usuario
(100 paginas)
(100 paginas)
Hardware De La Computadora Canoga-perkins 9145E10G Network Interface Device Hardware Manual de usuario
(55 paginas)
(55 paginas)
Hardware De La Computadora Canoga-perkins 9145E10G NID Software Version 1.0 Manual de usuario
(116 paginas)
(116 paginas)
Hardware De La Computadora Canoga-perkins 9145EMP Network Interface Device Hardware Manual de usuario
(50 paginas)
(50 paginas)
Hardware De La Computadora Canoga-perkins 9145EMP NID Software Version 3.1 Manual de usuario
(202 paginas)
(202 paginas)
Hardware De La Computadora Canoga-perkins 9145EMP NID Software Version 4.0 Manual de usuario
(229 paginas)
(229 paginas)
Hardware De La Computadora Canoga-perkins 9145ELB NID Software Version 4.01 Manual de usuario
(152 paginas)
(152 paginas)
Hardware De La Computadora Canoga-perkins 9145E Network Interface Device Quick Start Guide Manual de usuario
(7 paginas)
(7 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.122 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales